欢迎访问机床与液压官方网站!

咨询热线:020-32385312 32385313 RSS EMAIL-ALERT
轴承研磨机加工流场的参数优化及实验分析
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金项目(51205073);国家星火计划项目(2013GA780063); 广东省水利科技创新项目(2012-11); 广东省高等学校科技创新项目(2013KJCX0142);广州市科技计划项目(2012J4100053); 浙江大学流体动力及机电系统国家重点实验室开放基金项目(GZKF-201201); 西南交通大学牵引动力国家重点实验室开放基金项目(TPL1311)


Parameter Optimization and Experimental Analysis of the Flow Field in Bearing Grinding Machine
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为了探索研磨机研磨流场的较优加工参数,应用FLUENT对不同压力入口以及同一压力入口下不同入口磨料流气相百分比的加工流场进行了数值模拟,对参数优化后的研磨机进行实验研究。模拟结果表明:当入口压力在03~08 MPa时,流场存在较优工作压力,速度下降值较小,有利于磨削加工;当入口压力超过08 MPa时,随着入口压力的增加,速度下降值也会增大,动能损失变大,所以在加工时,尽量保持入口压力小于08 MPa,提高研磨机效率;相同入口压力下,磨料流气相百分比的增加,也会导致流场速度突变的状况,降低磨料流气相的百分比可以提高研磨机效率。实验结果表明:优化加工参数后能获得较好的工件金属表面效果。

    Abstract:

    In order to investigate the optimum processing parameters of the flow field in bearing grinding machine,numerical simulation was operated on the condition of different pressure intet and under the same inlet pressure but different percentage of the vapour phase by using FLUENT software.Results show that when the inlet pressure ranges from 03 MPa to 08 MPa,flow field presents the optimum working pressure,and less decrement of flow velocities,which facilitates grinding operation in return.On the other hand,when the inlet pressure higher than 08 MPa,the velocity decrement will be intensified along with the increasing inlet pressure. Therefore it is suggested to keep the inlet pressure lower than 08 MPa,which improves the grinding efficiency in practice.With the same inlet pressure,the break phenomenon of flow field will happen together with the percentage increment of abrasive vapour phase,thus for the purpose of improving the efficiency of grinding machine,it is suggested to reduce the percantage of the vapour phase in the abrasive stuff.Experimental results demonstrate that a better surface finish of workpiece can be ensured by optimizing those machining parameters.

    参考文献
    相似文献
    引证文献
引用本文

廖少棚,梁忠伟,刘晓初,周俊辉,谢碧洪.轴承研磨机加工流场的参数优化及实验分析[J].机床与液压,2015,43(17):39-43.
. Parameter Optimization and Experimental Analysis of the Flow Field in Bearing Grinding Machine[J]. Machine Tool & Hydraulics,2015,43(17):39-43

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2015-11-24
  • 出版日期: